Swissmade
NEWS
29/07/2020
MEASUREMENT

mmWave ½SAM Phantoms Extend OTA Testing in CATR for 5G FR2 Devices

SPEAG’s two new mmWave ½SAM phantoms are optimized for testing mobile phone and other ear-mounted devices in talk mode at frequencies from 6 to >100 GHz and meet the quiet zone and weight restrictions of mmWave CATR and OTA chambers.

With the release of the new mmWave ½SAM right and left head phantoms, SPEAG is extending the frequency coverage from <0.3 – 6 GHz to 0.3 – >100 GHz, thus allowing its customers to perform reliable and repeatable over-the-air (OTA) performance evaluations of devices including 5G New Radio Frequency Range 2 and any other mmWave wireless operating systems. The mmW-½SAMR/L-V11 packages consist of the right or left head phantom, the mounting structure, a 6-degree positioning mask, and our universal talk-mode fixtures compatible with all of our talk-mode hands. Each package:

  • is fully compliant with the target values of current and future CTIA test plans and the reflection properties of the human skin for frequencies >100 GHz;
  • is optimized for use in compact antenna test ranges (CATR) or other chambers for OTA evaluations with a 30 cm quiet zone or larger;
  • has a half-head geometry compliant with SAM data as defined by IEEE, 3GPP, and CTIA and is available for right and left-hand usage, whereas the deviation to the full SAM head phantom is <0.2 dB for frequencies >6 GHz;
  • is light weight with only 2.5 kg.

The new mmW-½SAMR/L-V11 phantom packages are an advanced solution for passive and active OTA testing from 6 to >100 GHz.

To receive a quotation or for further information, please contact us at info@speag.swiss.

CORPORATE

11/10/2013

Contact
info@speag.swiss

 

Successful Annual SPEAG Workshop in Korea

Following a tradition for almost 15 years, Dymstec and SPEAG have conducted another very successful annual workshop in Korea featuring a series of bright new stars.

 
MEASUREMENT

06/09/2013

Contact
info@speag.swiss

 

New SAR Measurement Standard Published

A new international standard for SAR measurements, IEEE 1528-2013, was published on 6 September, incorporating new procedures to improve testing efficiency while maintaining excellent measurement reproducibility and low uncertainty.

 
MEASUREMENT

04/09/2013

Contact
info@speag.swiss

 

Confined Loop Antenna (CLA) 30 MHz - 220 MHz

Confined loop antenna (CLA) are system validation antennas for the system checks with tissue simulating media at frequencies below 300 MHz.

 
SIMULATION

13/08/2013

Contact
semx-support@speag.swiss

 

SEMCAD X v14.8.4 Update Release

The SEMCAD X Team is pleased to announce the release of SEMCAD X v14.8.4, an update of SEMCAD X Aletsch v14.8.

 
MEASUREMENT

08/07/2013

Contact
info@speag.swiss

 

DAKS – Dielectric Measurements Have Never Been So Easy

SPEAG is delighted to announce the release of its latest innovation: a low-cost, portable, and easy-to-use Dielectric Assessment Kit System (DAKS) covering the frequency range between 200 MHz – 14 GHz.

 
MEASUREMENT

01/06/2013

Contact
info@speag.swiss

 

ANSI/AAMI PC69 (2007) Implant EMC Dipoles (450 – 3000 MHz)

A set of new dipoles has been developed for electromagnetic compatibility testing of active implantable medical devices according to ANSI/AAMI PC69-2007.

 
CORPORATE

31/05/2013

Contact
info@speag.swiss

 

Successful SPEAG workshops in Taipei, Beijing, Shenzhen, and Shanghai

Continuing a tradition of spring roadshows, Auden and SPEAG have just completed a series of successful hardware & software workshops in Taipei, Beijing, Shenzhen, and Shanghai.

 
CORPORATE

12/04/2013

Contact
info@speag.swiss

 

Successful Finalization of the SEAWIND Project

Three years after its start, the SEAWIND project was successfully finalized.

 
MEASUREMENT

11/04/2013

Contact
info@speag.swiss

 

DASY52.8.6 and SEMCAD X V14.6.9 Software Release

SPEAG is pleased to announce the release of DASY52.8.6 (1115) and SEMCAD-X V14.6.9 (7117). 

 
SIMULATION

02/04/2013

Contact
semx-support@speag.swiss

 

SEMCAD X v14.8.3 Update Release

The SEMCAD X Team is pleased to announce the release of SEMCAD X v14.8.3, an update of SEMCAD X Aletsch v14.8.

 
Page 20 of 29
 
 
Latest News