Swissmade
NEWS
16/10/2019
MEASUREMENT

DASY6 V6.10 Packed with Innovation: SAR/PD at 6 – 10 GHz, 5G NR Signals, and Full FCC Acceptance

DASY6 is the first system on the market that supports specific absorption rate measurements between 6–10 GHz, estimates epithelial power density (IEEE) or transmitted power density (ICNIRP) values, and includes 5G NR signals.

Following the release of DASY6 Module mmWave V2.0 one month ago, we have issued our new software cDASY6 V6.10. This release closes the gap regarding full compatibility with the latest standard version IEC/IEEE 62209-1528 by covering the full frequency range from 4 MHz ‒ 10 GHz for specific absorption rate (SAR) compliance testing. In addition, SPEAG once again offers solutions that are now discussed in the standard working groups, namely (i) estimates of the transmitted power density (PD) values that will become an additional exposure limit with the new safety guidelines of ICNIRP and IEEE and (ii) test signals for the new 5G New Radio (NR).

The key new features of cDASY6 V6.10 are:

  • SAR assessment between 6 – 10 GHz
  • estimation of epithelial PD (IEEE) or transmitted PD (ICNIRP) values
  • 6 ‒ 10 GHz system check dipoles and their target values (6.5, 7, 8, and 9 GHz)
  • calibration services for the frequencies between 6 – 10 GHz with +/-500 MHz bandwidth
  • sensor model calibration (SMC) extension to 5G NR signals
  • our Optimized Probe Positioning Technique (or ‘Mother Scan’) that makes testing much faster; it includes all additional features and checks which have been requested by regulators and has been formally approved by FCC
  • full compatibility with the recently published IEC 62209-2 AMD1:2019 on zoom scan grid resolution requirements

Transmitted PD Measurements Between 6 – 10 GHz

With the opening of the 6 GHz band for unlicensed use by the regulators, Wi-Fi technologies in this frequency range are announced to be introduced in 2020. SPEAG, being always one step ahead of standardization, has therefore extended the DASY6 measurement capability to frequencies up to 10 GHz. With cDASY6 V6.10, you can now assess the SAR for up to 10 GHz. This frequency extension does neither require new probes, nor new media or phantoms. Users only need to acquire the corresponding dipoles and calibration for the EX3DVx probes. SPEAG has also already implemented a novel technique developed by the IT'IS Foundation (paper to be released soon) to derive epithelial PD (IEEE) or transmitted PD (ICNIRP) values from the acquired SAR measurements that is made available to the user.

With the introduction of cDASY6 V6.10, DASY6 is the first system on the market fully compatible with the latest draft and soon to be released standard IEC/IEEE Draft 62209-1528.

Watch the video below for a life demo of the new software, or for more details on the procedure for devices operating at 6 - 10 GHz consult our application note.

 

Formal FCC Approval of Optimized Probe Positioning Technique

The Optimized Probe Positioning technique, also known as “Mother Scan”, implemented in cDASY6 reduces the scanning time while maintaining the same measurement uncertainty. The procedure consists of measuring the phantom surface at different locations with the MSTV1 / TP6V2 Phantom Teaching System. Once complete, an advanced algorithm generates the exact CAD model of the phantom. This technique also enables accurate SAR measurements in phantoms with strong curvatures such as Wrist or Face-Down.

During the last few weeks, SPEAG has implemented the latest monitoring/checks requested by FCC such that this technique is now fully approved by the FCC for measurements performed with Module SAR V6.10 or higher!

Compatibility with IEC 62209-2 Amendment

The IEC 62209-2 AMD1:2019 requires verification whether the grid resolution used for the Zoom Scans is sufficient. This feature, already made available in V6.4, has been updated to the latest standard requirements. cDASY6 V6.10 computes the radius and decay of the measured SAR distribution and verifies that the measurement grid is fine enough. In cases where it is not, the software suggests optimized grid settings. In addition, the 3 dB radius and the ratio between the peaks of the two lowest measurement planes are available in the reporting tool of the new software version.

Check our application note for more details.

SMC Extension to 5G NR Communication Systems for DASY6 and cSAR3D

As another novelty, the SMC procedure is now available for to 5G NR. From now on, probes calibrated for SMC will include linearization parameters for over 100 5G NR signals. These parameters are offered to our customers without any additional cost. cDASY6 operated with SPEAG’s Modulation and Audio Interference Analyzer (MAIA) and SMC calibrated probes ensures accurate and reliable SAR assessments.

The new cDASY6.10 software can be downloaded here.

The new cSAR3D V3.1 software with the 5G NR signals enabled can be downloaded here.

Any comments or questions? Please contact us at info@speag.swiss.

 

MEASUREMENT

04/04/2017

Contact
info@speag.swiss

 

SPEAG’s & CTIA’s New Forearm Phantom SHO-GFPC-V1

Standardized Over-The-Air (OTA) evaluation of wrist-worn devices in a precise and repeatable fashion.

 
MEASUREMENT

14/03/2017

Contact
info@speag.swiss

 

New OTA Phantom Optimized for Testing Head-Mounted Wearables

SPEAG’s new OTA phantom SAM V4.6BSE provides maximum flexibility for testing wearable devices mounted to the head.

 
MEASUREMENT

07/03/2017

Contact
info@speag.swiss

 

Quick cSAR3D Measurement of Wireless Device

Fast SAR measurements are easier than ever! Watch a new user video demonstrating the features of cSAR3D V2.8.

 
MEASUREMENT

28/02/2017

Contact
info@speag.swiss

 

cSAR3D Measurements in Great Demand

China Telecommunication Technology Labs-Terminals (CTTL-Terminals), China’s premier wireless testing authority, is now routinely applying SPEAG’s vector measurement-based array system cSAR3D for pre-compliance evaluations of wireless devices for several of China’s manufacturers.

 
MEASUREMENT

25/02/2017

Contact
info@speag.swiss

 

Brief Update: IEC 62209 Standard Meeting Exceeds Expectations

cSAR3D closes the gap between innovation and Compliance.

 
MEASUREMENT

21/02/2017

Contact
info@speag.swiss

 

New Holder Adaptor Eliminates All Steps on Testing Its Influence on SAR

The new low-loss low-permittivity adaptor eliminates all steps on testing the holders influence on SAR measurements.

 
MEASUREMENT

02/02/2017

Contact
info@speag.swiss

 

Making Waves: Revolutionary Probe for 5G

The novel EUmmWV2 probe enables precise very close near-field measurements for frequencies up to 110 GHz.

 
CORPORATE

01/02/2017

Contact
info@speag.swiss

 

Zurich43 Retreat 2017 at Pilatus Kulm - Communication

Twenty-five Zurich43 associates and three IT'IS Foundation board members gathered in the historic Hotel Pilatus-Kulm high above Luzern 30 – 31 January 2016 for their annual retreat, this year on communication. The goal of the two-day retreat was to find ways to improve communication skills across various target groups, channels, and markets, both within Z43 and with the outside world.

 
MEASUREMENT

27/01/2017

Contact
info@speag.swiss

 

cSAR3D Cal Lab

SPEAG invests in the future of dry SAR testing systems: New standards drive dedicated Cal Lab

In order to comply with the requirements of the upcoming IEC 62209/ Part 3 SAR testing standards, SPEAG has set up a dedicated laboratory for calibrating ‘dry’ SAR testing systems at their manufacturing facility located in the heart of Zurich. The laboratory complements their already existing and well-established ‘wet’ SAR system service centre.

 
CORPORATE

24/01/2017

Contact
info@speag.swiss

 

X-TRA, X-TRA! Inaugural Zurich43 Party: X-TRAordinary Nine = X-TRAordinary Fun!

The 2017 Z43 annual party held at Zurich’s X-TRA concert hall celebrated the emerging corporate identity and global reach of the Z43 brand.

 
Page 9 of 27
 
 
Latest News