Swissmade
NEWS
09/11/2021
MEASUREMENT

DASY8 Module HAC2019 (ANSI C63.19-2019)

SPEAG has released DASY8 Module HAC2019. The new module provides a guided workflow that demonstrates the compliance of any wireless device with the latest Hearing Aid Compatibility standard ANSI C63.19-2019 and the latest Federal Communication Commission requirements. Module HAC2019 is also available for DASY6.

Demonstrating Hearing Aid Compatibility (HAC) is important for warranting the electromagnetic and operational compatibility of hearing aids and wireless devices. In February 2021, the Federal Communication Commission (FCC) announced the adoption of the 2019 edition of ANSI C63.19, the “American National Standard Methods of Measurement Compatibility Between Wireless Communications Devices and Hearing Aids,” which became effective June 4, 2021. The FCC is giving manufacturers a two-year transition period (i.e., until June 4, 2023) to adopt the requirements of the updated ANSI C63.19-2011 standard. It has also extended the volume control deadline to match this transition period. Beginning June 5, 2023, only test reports that comply with ANSI C63.2019 will be accepted.

Following SPEAG’s tradition of staying ahead of requirements, we started early with the development of Module HAC2019 for DASY8/6 users. This is a completely new software solution based on SPEAG’s latest graphical user interface technology that guides users through the compliance workflow by using specific Jupyter Notebooks. The DASY8/6 system is interfaced via a dedicated application programming interface.

During development, we have been meticulous in ensuring that we reuse as much as possible of the previous HAC hardware in order to save resources and costs for our customers. The only element that has been replaced is the audio interference analyzer (AIA), which has been superseded by the modulation and audio interference analyzer (MAIA) to evaluate the modulation interference factor (MIF).

DASY8/6 Module HAC2019 consists of four Jupyter Notebooks that represent the different steps of the compliance workflow:

  • MIF measurements with MAIA
  • Simplified verification of the radiofrequency (RF) test setup using RF emission calibration dipoles
  • Evaluation of the wireless device RF interference potential by determining the RF audio interference level (RFail)
  • Measurement of the baseband (audio frequency) magnetic T-Coil (Tele-Coil) signal from a wireless device.

The workflow can easily be implemented, as shown in this video:

MIF Measurements with MAIA

The MAIA allows verification of the MIF values used to calculate the RFail. The MAIA can be operated over the air interface using the built-in ultra-broadband planar log spiral antenna (supported frequency range: 698–6000 MHz) or in conducted mode using the coaxial SMA 50 Ω connector (supported frequency range: 300–6000 MHz).

MIF

Figure 1: MIF Measurement of a 5G new radio frequency range 1 frequency division duplex signal

RF Test Setup Verification

A dedicated Notebook has been developed for verifying the RF interference measurement setup. The user can select and optimize the measurement configuration in a list of predefined templates. Peak values are automatically detected for easy comparison with the measurement targets.

SystemCheck

Figure 2: Interpolated E-field Distribution of a CD2450V3 Dipole

RF Audio Interface Level Determination

In Module HAC2019, the RFail is assessed using the (preferred) indirect test procedure described in ANSI C63.19-2019. A 50x50 mm region centered on the speaker location is scanned and the root mean square (RMS) electric field values are recorded at each point. Once the scan is completed, the RFail is obtained by adding the MIF value to the average steady RMS field strength averaged over the measurement area.

RF

Figure 3: Interpolated E-field distribution of a wireless device after MIF scaling

Baseband Magnetic T-Coil Signal

The Jupyter Notebook developed for baseband magnetic T-Coil testing guides the users through the measurement steps described in the ANSI C63.19-2019:

  • Validation of the measurement equipment using a telephone magnetic field simulator (TMFS) or a Helmholtz coil
  • Determination of the wireless device drive levels for each audio signal
  • Measurement of the desired magnetic field with a voice-like signal (desired audio band magnetic (ABM) signal)
  • Measurement of the frequency response at the maximum location of the desired ABM signal
  • Measurement of the undesired broadband audio magnetic signal (undesired ABM signal)

The T-Coil coupling qualifying strengths, including determination of the primary and secondary groups, as well the magnetic field frequency response are computed by the post-processor and are available for visualization and reporting.

Groups2

Figure 4: Evaluation of Primary and Secondary Groups according to ANSI C63.19-2019

The software installer will be available on November 15th.

For further information, please contact us at info@speag.swiss or any of our sales channels.

 

MEASUREMENT

12/06/2018

Contact
info@speag.swiss

 

Release of New OTA Phantom Series for 5G and IoT

SPEAG released a new generation of phantoms covering the entire frequency range from 3 GHz to over 100 GHz. The solution is both simple and elegant and improves the surface quality and sustainability of the phantoms.

 
MEASUREMENT

06/06/2018

Contact
info@speag.swiss

 

5G Module V1.2: Offering More Automation, Features and Speed

Power density compliance testing has never been easier: SPEAG’s latest software release, Version 1.2 of our 5G Module, is yet another step forward in our drive to provide you with even more automated and more versatile tools for analysis and assessment of compliance at frequencies above 10 GHz!

 
CORPORATE

28/05/2018

Contact
info@speag.swiss

 

13th Annual Hardware and Software Workshop Series in Taiwan and China Organized by AUDEN Technology Corporation

Another Successful Hardware and Software Workshop for SPEAG and ZMT Zurich MedTech AG in Taipei, Beijing, Shanghai, and Shenzhen in May 2018.

 
SIMULATION

25/05/2018

Contact
semx-support@speag.swiss

 

SPEAG’s SEMCAD X 5G Toolkit Gets Tested for Phased-Array Antenna Design and Optimization

SEMCAD X’s 5G Toolkit put to the test: A user video demonstrates the design workflow of on-device phased-array antennas by exploiting the features of the new SEMCAD X 5G Toolkit, including the unique worst-case power density evaluator.

 
MEASUREMENT

11/04/2018

Contact
info@speag.swiss

 

cDASY6 V6.6 – Ready for IoT Compliance Testing

SPEAG released cDASY6.6 which is fully compatible with IEC 62232 and the voting drafts of IEC 62209-U / IEC 62209-3 and from which DASY6 customers can benefit with immediate effect.

 
SIMULATION

20/02/2018

Contact
semx-support@speag.swiss

 

SEMCAD X Matterhorn Release V17.0

SPEAG is proud to announce a major release of SEMCAD X Matterhorn V17.0! With the new release, we are particularly proud to make our innovative and easy-to-use multi-parameter, multi-goal Optimizer Framework V1 available to all of our customers.

 
MEASUREMENT

13/02/2018

Contact
info@speag.swiss

 

cDASY6.6 Beta-Release

Ahead of the official release of cDASY6.6 on March 6, 2018, SPEAG has made a Beta version available for early adopters. cDASY6.6 includes many striking features, such as the full integration of specific phantoms, and the Fast Volume Scan.

 
MEASUREMENT

06/02/2018

Contact
info@speag.swiss

 

cSAR3D-A: Fully Automated SAR Testing

cSAR3D-A Version 1 combines the most reliable vector-based array system cSAR3D with the precision robot of DASY6. It enables fully automated SAR evaluations with thousands of single SAR measurements - with only one click.

 
CORPORATE

19/01/2018

Contact
info@speag.swiss

 

SPEAG and ZMT Sales Agents Event 2018

Sales agents representing SPEAG and ZMT Zurich MedTech AG (ZMT) products around the globe convened at Z43 17 – 19 January 2018 to learn about the whole range of products and technologies and the latest developments. Representatives from both long-time and new partners attended the 3-day event, which was a great opportunity for fruitful and in-depth discussions and face-to-face information transfer.

 
CORPORATE

19/01/2018

Contact
info@speag.swiss

 

Game On! Z43’s Annual Party, 2018 “The Next Level” Edition!

The annual Zurich 43 party, this year with the gamer theme “The Next Level”, was held at Halle 622 in Zurich-Oerlikon on Friday 19 January 2018.

 
Page 9 of 31
 
 
Latest News