Swissmade
NEWS
09/11/2021
MEASUREMENT

DASY8 Module HAC2019 (ANSI C63.19-2019)

SPEAG has released DASY8 Module HAC2019. The new module provides a guided workflow that demonstrates the compliance of any wireless device with the latest Hearing Aid Compatibility standard ANSI C63.19-2019 and the latest Federal Communication Commission requirements. Module HAC2019 is also available for DASY6.

Demonstrating Hearing Aid Compatibility (HAC) is important for warranting the electromagnetic and operational compatibility of hearing aids and wireless devices. In February 2021, the Federal Communication Commission (FCC) announced the adoption of the 2019 edition of ANSI C63.19, the “American National Standard Methods of Measurement Compatibility Between Wireless Communications Devices and Hearing Aids,” which became effective June 4, 2021. The FCC is giving manufacturers a two-year transition period (i.e., until June 4, 2023) to adopt the requirements of the updated ANSI C63.19-2011 standard. It has also extended the volume control deadline to match this transition period. Beginning June 5, 2023, only test reports that comply with ANSI C63.2019 will be accepted.

Following SPEAG’s tradition of staying ahead of requirements, we started early with the development of Module HAC2019 for DASY8/6 users. This is a completely new software solution based on SPEAG’s latest graphical user interface technology that guides users through the compliance workflow by using specific Jupyter Notebooks. The DASY8/6 system is interfaced via a dedicated application programming interface.

During development, we have been meticulous in ensuring that we reuse as much as possible of the previous HAC hardware in order to save resources and costs for our customers. The only element that has been replaced is the audio interference analyzer (AIA), which has been superseded by the modulation and audio interference analyzer (MAIA) to evaluate the modulation interference factor (MIF).

DASY8/6 Module HAC2019 consists of four Jupyter Notebooks that represent the different steps of the compliance workflow:

  • MIF measurements with MAIA
  • Simplified verification of the radiofrequency (RF) test setup using RF emission calibration dipoles
  • Evaluation of the wireless device RF interference potential by determining the RF audio interference level (RFail)
  • Measurement of the baseband (audio frequency) magnetic T-Coil (Tele-Coil) signal from a wireless device.

The workflow can easily be implemented, as shown in this video:

MIF Measurements with MAIA

The MAIA allows verification of the MIF values used to calculate the RFail. The MAIA can be operated over the air interface using the built-in ultra-broadband planar log spiral antenna (supported frequency range: 698–6000 MHz) or in conducted mode using the coaxial SMA 50 Ω connector (supported frequency range: 300–6000 MHz).

MIF

Figure 1: MIF Measurement of a 5G new radio frequency range 1 frequency division duplex signal

RF Test Setup Verification

A dedicated Notebook has been developed for verifying the RF interference measurement setup. The user can select and optimize the measurement configuration in a list of predefined templates. Peak values are automatically detected for easy comparison with the measurement targets.

SystemCheck

Figure 2: Interpolated E-field Distribution of a CD2450V3 Dipole

RF Audio Interface Level Determination

In Module HAC2019, the RFail is assessed using the (preferred) indirect test procedure described in ANSI C63.19-2019. A 50x50 mm region centered on the speaker location is scanned and the root mean square (RMS) electric field values are recorded at each point. Once the scan is completed, the RFail is obtained by adding the MIF value to the average steady RMS field strength averaged over the measurement area.

RF

Figure 3: Interpolated E-field distribution of a wireless device after MIF scaling

Baseband Magnetic T-Coil Signal

The Jupyter Notebook developed for baseband magnetic T-Coil testing guides the users through the measurement steps described in the ANSI C63.19-2019:

  • Validation of the measurement equipment using a telephone magnetic field simulator (TMFS) or a Helmholtz coil
  • Determination of the wireless device drive levels for each audio signal
  • Measurement of the desired magnetic field with a voice-like signal (desired audio band magnetic (ABM) signal)
  • Measurement of the frequency response at the maximum location of the desired ABM signal
  • Measurement of the undesired broadband audio magnetic signal (undesired ABM signal)

The T-Coil coupling qualifying strengths, including determination of the primary and secondary groups, as well the magnetic field frequency response are computed by the post-processor and are available for visualization and reporting.

Groups2

Figure 4: Evaluation of Primary and Secondary Groups according to ANSI C63.19-2019

The software installer will be available on November 15th.

For further information, please contact us at info@speag.swiss or any of our sales channels.

 

MEASUREMENT

28/03/2013

Contact
info@speag.swiss

 

New DAK Movie

Release of a brief training video with tips on how to increase the precision of dielectric measurements.

 
MEASUREMENT

14/03/2013

Contact
info@speag.swiss

 

TDS (Time Domain Sensor) Release*

We are pleased to announce the release of our TDS Standalone systems. TDS Standalone is the first product of our growing TDS product range to employ SPEAG’s novel active optical sensor technology for E- and H-field measurements in the frequency range from 10 MHz – 6 GHz.

*available in the US and Canada after final certification in accordance with the regulations of the US FDA, CDRH, CFR 21, Section I, subchapter J, part 1002 to 1040.11 (expected in May 2013).

 
MEASUREMENT

04/03/2013

Contact
info@speag.swiss

 

Solid Spacer V2

We are pleased to announce the release of the optimized spacers SPACERS V2 for our CTIA hand phantoms SHO X.

 

 
MEASUREMENT

25/02/2013

Contact
info@speag.swiss

 

New Product: POPEYE

In response to customer requests for more versatile phantoms, SPEAG introduces several new whole-body and hand phantoms.

 
MEASUREMENT

11/02/2013

Contact
info@speag.swiss

 

DAK-1.2 Release & Software Update

We are pleased to announce the release of the optimized high frequency dielectric probe DAK-1.2 covering the frequency range 5 – 50 GHz. At the same time, we extended and improved the features of our software that is now available for download. 

 
CORPORATE

19/01/2013

Contact
info@speag.swiss

 

Electrified into 2013

The most spectacular Annual Party in recent memory: the IT'IS - Speag - ZMT "Electrified into 2013 Party".

 
MEASUREMENT

14/01/2013

 

Audio Interference Analyzer (AIA)

This AIA enables the DASY52 Users to directly measures the Modulation Interference Factor (MIF) and the Probe Modulation Factor (PMF) of modulated radiofrequency (RF) signals. It is also perfectly suited for establishing the connection between base-station emulator and the device under test (DUT). 

 
SIMULATION

21/12/2012

Contact
semx-support@speag.swiss

 

SEMCAD X v14.8.2 Update Release

The SEMCAD X Team is pleased to announce the release of SEMCAD X v14.8.2, an update of SEMCAD X Aletsch v14.8.

 
CORPORATE

30/11/2012

Contact
info@speag.swiss

 

Innovation Retreat

The success and achievements of the Bell Labs have inspired generations of engineers, physicists, product developers, and other scientists. These accomplishments and the success stories of our greatest inventors have also inspired 21 Speag, ZMT, and IT'IS coworkers who gathered in Flüeli-Ranft on Novenber 22nd-23rd to get under the hood of our our own innovation engine.

 
SIMULATION

12/11/2012

Contact
semx-support@speag.swiss

 

MUSAIK v1.3 Release

The MUSAIK and SEMCAD X Team is pleased to announce the release of MUSAIK v1.3, a feature release of Musaik.

 
Page 23 of 31
 
 
Latest News