Jun 6, 2023

DASY8/6 Module WPT V2.0: Enhanced and Fast WPT Compliance Testing

SPEAG released DASY8/6 Module WPT V2.0, which integrates the new MAGPy Version 2 with the DASY8/6 system and provides 8-times faster, more accurate, and total field (magnetic and electric field) compliance testing of sources emitting any periodic signals (<10 MHz) against the basic restrictions.

The latest version of our DASY8/6 Module WPT, V2.0, is now based on MAGPy Version 2 and takes full advantage of this stand-alone product. Evaluating wireless power transfer (WPT) systems has never been so quick and easy with maximum precision:

  • 8× faster measurements, as the new probes allow assessment of the eight isotropic magnetic (H-)field probes (23 sensors plus phase) at each robot position;
  • Simultaneous measurement of the incident electric (E-)field with its integrated isotropic E-field sensor;
  • Evaluation of periodic signals with non-sinusoidal waveforms and duty cycles;
  • Evaluation of all basic restriction quantities, now also including the local non-averaged induced E-field required by ISED;
  • Conversion of the measured H-field distribution into a Maxwell field and calculation of the fields in the standardized phantom without loss of precision (Tier 4 of IEC 63184);
  • Conservative estimation of the fields induced in the tissue by the incident E-field according to Christ et al. (Bioelectromagnetics, 43(7), 2022).

This user video shows how the MAGPy Version 2 probe, integrated with DASY8/6 Module WPT V2.0, is used to determine compliance for wireless power transfer devices.

Another important advantage is the dual use of the MAGPy system as a hand-held system (MAGPy Version 2) and as part of Module WPT (DASY8/6 Module WPT V2.0), as customers only need to buy and calibrate one device.

If you have any suggestions or would like to receive further information, please contact us at

Kind regards,

Your DASY Team



Aug 18, 2020



cDASY6 Module WPT Pre-Release – Our New MAGPy Technology for DASY6

SPEAG’s new cDASY6 Module WPT is the first-ever solution to demonstrate compliance with the basic restrictions of any magnetic source according to the latest IEC/IEEE63184 DPAS draft. The module is based on SPEAG’s new MAGPy product line.


Jul 29, 2020



mmWave ½SAM Phantoms Extend OTA Testing in CATR for 5G FR2 Devices

SPEAG releases the new mmW-½SAMR/L-V11 phantom packages for over-the-air testing at frequencies from 6 to >100 GHz.


Jul 28, 2020



Publications Confirm: DASY6 is the Most Accurate SAR System

Scientific debate corroborates that SPEAG's DASY6 probe-scanning system has low measurement errors (<3%) for simple antennas and provides further support of the robustness of the latest IEC 62209 standard


Jul 22, 2020



DASY6 and cSAR3D: Detailed Guidance for 5G NR FR1

Two new Application Notes provide detailed guidelines for testing 5G NR FR1 radios using DASY6 and cSAR3D. Also, SPEAG’s calibration lab just received ISO/IEC 17025 accreditation.


Jun 25, 2020



Z43 Goes Carbon Dioxide-Free

SPEAG is getting greener! We have installed a new energy system consisting of solar panels and a groundwater-based heat pump. We are proud that we have started to generate our own power and have become largely CO2-free.


Jun 18, 2020



cDASY6 Module SAR V6.14: Time-Efficient SAR Evaluation Thanks to Smart Zoom Scan

Smart Zoom Scan in cDASY6 Module SAR V6.14: Simplified and accelerated workflow for SAR compliance testing.


Jun 15, 2020



mmWave THG-Phantom Package for OTA Tests of 5G NR F2 Devices

SPEAG releases the two-hand-grip phantom package and fixture optimized for OTA testing in compact mmWave chambers.


May 19, 2020



SEMCAD X Matterhorn V18.2.2 Release

SPEAG announced the release of SEMCAD X Matterhorn V18.2.2, an updated version of SEMCAD X Matterhorn  V18.2.


May 6, 2020



cDASY6 Module SAR V6.12: Automate Your Testing Workflow

New application programming interface enables users to perform quicker, easier, and customized SAR compliance testing by automation of workflows.


May 5, 2020



New Software Release DAK V2.6.1.1

We are pleased to announce the latest software release of our DAK product line, version Along with our recent DAK-TL hardware upgrade, this important maintenance release further improves the accuracy and  repeatability of measurements with our DAK product line and extends the capability of high permittivity assessments with DAK-TL.

Page 5 of 33
Latest News