Swissmade
NEWS
19/02/2019
MEASUREMENT

Release of cDASY6 Module mmWave V1.6

SPEAG’s latest software release incorporates many new features and improvements to facilitate power compliance testing of devices operating >10 GHz

With cDASY6 Module mmWave V1.6, power density compliance testing is now easier than ever:

  • A new Generic Scan that allows determination of the power density with the far-field approximation based on a single plane measurement has been added. Now, assessments valid in the far-field and quasi-far-field are much faster compared to generally valid 2-plane method with phase reconstruction
  • The Generic Scan also allows to determine the E-field amplitude anywhere with a one plane measurement
  • The user can create test channels at any frequency
  • The grid settings are now more open, allowing more flexible and user-friendly operation of the software
  • The measurement grid can now be previewed for all scan types
  • The power density results for different averaging areas can now be visualized simultaneously
  • Completed measurements can be re-evaluated with different communication systems
  • The computation time to post-process scans has been speeded up by x4 on average
  • The report generator, in particular the screenshot functionality, has been improved
  • The measured data can now be exported at any grid resolution
  • The power density viewers show now the location of psSavg

New Generic 2D Scan

The new Generic 2D Scan is used to compute the E-field and estimate the power density on a rectangular two-dimensional grid. The power density value, derived from the E-field distribution without any phase reconstruction, is valid in the far-field only. cDASY6 allows the far-field distance to be determined as function of the antenna radius based on the latest research. This feature dramatically speeds up the time for measurements in the far-field region (by x8 on average).

cDASY6 mmWave Module V1.6 Generic Scan

Power distribution measured with the generic 2D scan in the far field from the source (1-plane)

Custom Test Channels

Custom test channels can be now added in V1.6. This feature allows to test at any frequency even for bands not yet added to the mmWave module.

Grid Settings Flexibility

The flexibility of the grid settings has been greatly improved in V1.6. It is now possible to:

  • Offset the position of the device-under-test relative to the reference point
  • Manually offset and resize the Fast Area Scan grid
  • Define the 5G scan-grid based on the Fast Area Scan

Further, measurements for all scan types can now be previewed.

cDASY6 mmWave Module V1.6 Grid Preview

Grid scan preview with cDASY6 Module mmWave V1.6

Re-Evaluation of Completed Measurements

With V1.6, we have added the possibility to re-evaluate already completed measurements with any communication system. The specificities in hardware (probes, DAE) design do not allow similar re-evaluations based on different hardware components. In these cases, new measurements with the desired hardware must be performed.

Post-Processing

Small but very important improvements to benefit our DASY6 users have been introduced in the post-processing procedure:

  • Power density distributions can now be computed and visualized simultaneously with different averaging areas
  • The computation time for post-processing of scans is on average 4× faster
  • By default, settings in the “options”-view are adjusted to user the needs
  • The measurement data can be exported at any grid resolution

Note that the post-processing algorithm itself has not been modified.

Report Generation

Review of the “report generator”-tool has resulted in the following improvements:

  • The size of the field plot can now be defined by the user for more consistent result reporting
  • The scalar bar is now considerably larger to improve overall readability

cDASY6 mmWave Module V1.6 Report Generator

E-field distribution measured with a 2D-generic scan in the near-field of the source

Improved Power Density Viewers

The power density viewers have been improved based on the feedback we have received from you:

  • The peak averaged power density is displayed with a grey circle
  • The averaged power density plots have now the same size as the measurement grid. The post processing algorithm uses zero padding to compute the averaged power density where the averaging circle would be truncated. This area is delimited by a dashed grey line on the plot. Averaged power density values outside this line might be underestimated and should not be considered as accurate.

cDASY6 mmWave Module V1.6 FRONT 2 00 0 CW 60000 00MHz 3dcDASY6 mmWave Module V1.6 Savg

Power Density S (left) and Averaged Power Density (right). The averaging circle shows the maximum of the averaged power density. Only values inside the dashed line should be considered as accurate

The next major cDASY6 software release, V2.0, will feature two major optional modules:

  • The Optimizer Module for determination of the worst-case power density of antenna arrays from a series of single-element measurements
  • The Forward Transform Evaluation (FTE) Module for evaluation of the power density distribution along any virtual surface (e.g., SAM Head) from a single measurement and estimation of the radiation pattern

For further information, please contact us at info@speag.swiss.

MEASUREMENT

19/02/2019

Contact
info@speag.swiss

 

Release of cDASY6 Module mmWave V1.6

SPEAG released the cDASY6 Module mmWave V1.6 with many small but important new features that make compliance testing and documentation easier and faster.

 
CORPORATE

29/01/2019

Contact
info@speag.swiss

 

Great Interest in Joint SPEAG / Vitec Exhibition and Workshop at Automotive World 2019 in Tokyo

Successful exhibition and workshop by SPEAG and VITEC at the Automotive World Conference 2019 in Tokyo, Japan.

 
CORPORATE

23/01/2019

Contact
info@speag.swiss

 

Zurich43 Retreat 2019 on Ethics & Z43 Culture

Zurich43's annual retreat was held 21 – 22 January 2019 to discuss "Ethics & Z43 Culture in Real or Perceived Devaluing Times" with a particular focus on fairness, justice, recognition, and populism.

 
SIMULATION

27/11/2018

Contact
semx-support@speag.swiss

 

SEMCAD X Matterhorn New Release V17.4

With the release of SEMCAD Matterhorn V17.4, SPEAG achieves another milestone by being the first manufacturer to offer a robust and effective method for estimating the maximum exposure of antenna arrays of any size on any arbitrary surface as required by the latest standards drafts.

 
CORPORATE

16/11/2018

Contact
info@speag.swiss

 

SPEAG Wins Award at Huawei Supplier Convention

SPEAG received an award for being in the top 11 suppliers worldwide for delivery of excellent quality products at Huawei’s Apparatus, Equipment & Office Supplies Procurement Qualification Department convention in Shenzhen, CN.

 
MEASUREMENT

16/10/2018

Contact
info@speag.swiss

 

CTIA's ANKLE and CHEST Phantoms Released Ahead of Test Plan Release

Another addition to the SPEAG phantom family: we released two new highly-specialized electromagnetic phantoms for over-the-air certification of wireless devices ‒ the generic ANKLE and generic CHEST phantom! These phantoms were developed in close collaboration with CTIA's OTA working group and are expected to be included in the upcoming CTIA test plans.

 
MEASUREMENT

04/10/2018

Contact
info@speag.swiss

 

FCC News and IEC Meeting Report

New updates from IEC TC106 standardization in Stockholm, TCB Council Workshop in Baltimore, and FCC Laboratory in Columbia, MD

 
MEASUREMENT

02/10/2018

Contact
info@speag.swiss

 

cDASY6: Now More Robust, More Responsive, and Faster

SPEAG released cDASY6 V6.8 and cDASY6 Module mmWave V1.4. Both include important and long-awaited new features that not only greatly improve the user experience but also make our DASY6 system even faster with improved precision.

 
SIMULATION

27/09/2018

Contact
semx-support@speag.swiss

 

SEMCAD X Matterhorn V17.2 Release

SPEAG is pleased to announce the release of SEMCAD X Matterhorn V17.2, an updated version of SEMCAD X Matterhorn  V17.0.1.

 
SIMULATION

18/09/2018

Contact
info@speag.swiss

 

Sim4Life light: Explore the World of Complex Physiological Modelling and Simulations – for Free!

SPEAG's partner organization ZMT announces the release of Sim4Life Light, a new edition specifically designed for students who can now use the cutting-edge computational life science platform for their research at no cost.

 
Page 1 of 25
 
 
Latest News