Swissmade
NEWS
25/06/2020
CORPORATE

Z43 Goes Carbon Dioxide-Free

As part of our effort to help create a sustainable and healthier future, energy at Z43 is now 100% renewable, which will lead to a reduction in CO2 emissions of more than 60,000 m3 per year – corresponding to about twenty times the CO2 footprint of the average Swiss.

For the past 20 years, we have produced the heating energy for the Z43 headquarters in Zurich – home to the IT’IS Foundation, Schmid & Partner Engineering AG, and ZMT Zurich MedTech AG – as well as supplied adjacent residential buildings with more than 79 apartments with natural gas. Our labs, on the other hand, were cooled via a small heat pump powered by electricity. Though gas is “cleaner” than oil or coal, we strongly felt that it was time to switch from fossil fuels to renewable sources of power in order to run our work lives more sustainably.

niels roof panels web

niels basement heating web

So we finally got rid of the gas burners in our basement and invested heavily in a new energy system. The newly installed 500 kW heat pump now heats and cools the various buildings by exchanging heat with the groundwater stream that runs 30 m below our premises. In addition, because our labs and servers produce more heating energy than we can use during the summer, we replaced the warm-water panels on the roof with photovoltaic cells to generate our electric power. We also took care to only subscribe to companies that exclusively generate electricity by hydro, wind, and solar power. This complements our internal policy that Z43 staff should only commute by car to work in exceptional circumstances (e.g., it was appropriate to do so during the COVID-19 pandemic).

We are proud that we have started to generate our own energy and have become largely CO2-free at Z43.

Curious how it looks? Check out our CO2-free energy production by clicking on the leaf:

leaf slogan mm3

The leaf can also be found in the header of any of our webpages: IT’IS Foundation, SPEAG, ZMT, and Zurich43.

Z43 – Think Renewable!

MEASUREMENT

23/12/2011

Contact
info@speag.swiss

 

Advance Notice: Next Generation of Probe Systems – TDS

We are proud to announce a breakthrough in EM probe systems. The Time-Domain-Sensor (TDS) is the basis of our novel product line of high-performance active optical radio-frequency field sensor systems. The TDS concept allows the measurement of the full complex vectorial EM field distribution (amplitude and phase) in the time and frequency domains. First TDS probes for E- and H-field measurements in the 10MHz to 6GHz frequency range will become available in the next quarter.

 
MEASUREMENT

22/12/2011

Contact
info@speag.swiss

 

DAK Release

Our first DAK shipments were made to customers in December. We are very pleased about the successful launch and strong customer interest in this new product line for high-precision dielectric measurements. Expansion of the frequency range and applications for the DAK product line will continue in 2012.

 
MEASUREMENT

09/12/2011

Contact
support@speag.swiss

 

iSAR Calibration Lab in Korea

SPEAG and Dymstec are delighted to announce the opening of the joint SPEAG Calibration Laboratory Korea, Inc. The laboratory is now fully operational and completed its first iSAR calibrations this month. iSAR calibration is performed using the same high-quality equipment and procedures as the SPEAG iSAR calibration laboratory in Zurich, with the additional benefit of much faster iSAR calibration service for many Asian customers.

 
SIMULATION

22/11/2011

Contact
semx-support@speag.swiss

 

MUSAIK v1.2 Release

The MUSAIK and SEMCAD X Team is pleased to announce the release of MUSAIK v1.2, a feature release of Musaik.

 
SIMULATION

27/10/2011

Contact
semx-support@speag.swiss

 

SEMCAD X EUMW Raffle Winner

At the end of the exhition at European Microwave Week 2011, a NVIDIA Tesla C1060 card was given away in a raffle.

 
MEASUREMENT

19/10/2011

Contact
info@speag.swiss

 

New Product: DAK (Dielectric Assessment Kit)

DAK is our new product line for high-precision dielectric measurements. Our probes are optimized for precision, robustness and ease of use. The software is flexible and operates with the most popular network analyzers on the market. The DAK system is calibrated by our ISO/IEC 17025 accredited laboratory.

 
SIMULATION

06/10/2011

Contact
semx-support@speag.swiss

 

SEMCAD X Promotions for EUMW 2011 Attendees

European Microwave Week 2011, Manchester, UK

SEMCAD X end-of-the-year promotions, only for conference attendees

 
SIMULATION

27/09/2011

Contact
semx-support@speag.swiss

 

SEMCAD X in Microwave Engineering Europe Magazine

SEMCAD X: Enhanced Simulation of Waveguide Structures

 
SIMULATION

02/09/2011

Contact
semx-support@speag.swiss

 

SEMCAD X v14.6.2 Update Release

The SEMCAD X Team is pleased to announce the release of SEMCAD X v14.6.2, an update of SEMCAD X Aletsch v14.6.

 
SIMULATION

26/08/2011

Contact
semx-support@speag.swiss

 

SEMCAD X Light v14.6.2 Release

The SEMCAD X Team is pleased to announce the release of SEMCAD X Light V14.6.2, a limited version of SEMCAD X v14.6.2 Aletsch.

 
Page 23 of 28